D-Link 8GE PoE+ 2GE Uplink 250m PoE Switch – DGS-F1010P

D-Link 8GE PoE+ 2GE Uplink 250m PoE Switch – DGS-F1010P

Lightning strikes and power surges do not announce themselves. In an outdoor CCTV installation or a remote access point deployment, a single surge event can destroy every connected device overnight. Running replacements, filing insurance claims, and rebuilding a network that was working yesterday is a cost that a switch with adequate surge protection prevents entirely. The D-Link DGS-F1010P Gigabit PoE surveillance switch carries 6KV lightning protection built into every port — making it the right choice for installations where the network is exposed to the elements.

Built for Environments Where Surges Are Real

The DGS-F1010P is a 10-port unmanaged Gigabit switch with 8 PoE ports and 2 uplink ports. It supports a 120W PoE budget across all eight ports and extends PoE reach to 250 metres in Extend mode. Four DIP-switch-controlled operating modes configure the switch for different deployment scenarios without software.

What sets it apart from similar-spec switches is the 6KV surge protection on every port. IP cameras mounted on building exteriors, access points on rooftops, and devices connected via long outdoor cable runs are all vulnerable to lightning-induced electrical surges. The DGS-F1010P is engineered to absorb that event rather than transmit it to every connected device.

6KV Lightning and Surge Protection on Every Port

The 6KV protection rating means the switch resists electrical surges up to 6,000 volts at the port level. A nearby lightning strike induces a voltage spike along cable runs. On an unprotected switch, that spike travels into every connected device simultaneously. On the DGS-F1010P, it stops at the port. Connected cameras, access points, and VoIP phones stay protected. Replacement and repair costs stay down.

Four DIP-Switch Modes for Different Deployments

A physical DIP switch on the unit selects between four operating modes — no software, no web interface, no configuration step required.

Extend mode stretches PoE and data reach to 250 metres using Cat5e or Cat6 cable at 10Mbps. VLAN mode isolates each PoE port from the others — connected devices communicate only through the uplink, not between themselves. QoS mode prioritises video traffic, reducing frame drops and buffering on surveillance streams. PoE mode automatically detects connected devices, monitors their status, and reboots any unresponsive device by cycling port power.

120W PoE Budget — 30W Per Port

The total PoE budget across all eight ports reaches 120W. Each port delivers up to 30W — covering PoE+ devices including high-power wireless access points, PTZ cameras, and IP intercoms. IEEE 802.3af (15.4W) and IEEE 802.3at (30W) devices both connect and receive the correct power level through automatic detection. Non-standard PoE devices and standard Ethernet switches connect safely — the auto-detection circuit prevents accidental power delivery to non-PoE equipment.

Verified Specifications

All data below is confirmed from the official D-Link DGS-F1010P product page and datasheet.

Ports and PoE Performance

• Model: DGS-F1010P (DGS-F1010P-E)
• PoE Ports: 8x 10/100/1000Mbps Gigabit PoE+ (RJ45, ports 1–8)
• Uplink Ports: 2x 10/100/1000Mbps Gigabit (RJ45, ports 9–10)
• PoE Standard: IEEE 802.3af / IEEE 802.3at
• PoE Budget: 120W total
• Max Per-Port PoE: 30W
• Max Extend Distance: 250 metres (Cat5e or Cat6, at 10Mbps)
• Surge Protection: 6KV lightning protection on all ports

Operating Modes and Build

• Mode Selection: Physical DIP switch — no software required
• Mode 1 — Extend: 250m PoE and data reach, ports 1–8
• Mode 2 — VLAN: Port isolation, suppresses network storms
• Mode 3 — QoS: Video traffic prioritisation for surveillance streams
• Mode 4 — PoE: Auto device detection, unresponsive device reboot
• Flow Control: IEEE 802.3x full-duplex, back pressure half-duplex
• Switching Method: Store and Forward
• Auto MDI/MDIX: Yes — uplink ports
• Housing: Fanless metal — silent passive cooling
• Operating Temperature: 0°C to 40°C
• Setup: Plug-and-play — no drivers or software required
• Network Standards: IEEE 802.3 / 802.3u / 802.3ab / 802.3af / 802.3at / 802.3x

Where the DGS-F1010P Gets the Work Done

The Outdoor CCTV Installation in a Lightning-Prone Area

IP cameras mounted on external walls, perimeter fences, or rooftops run cable through outdoor environments. A storm-season lightning event in Nairobi or any high-altitude area can send a surge across every connected cable simultaneously. The DGS-F1010P absorbs that surge at 6KV — protecting the NVR, the cameras, and the uplink router connected to the same switch. A surveillance system that stays operational after a storm is one that was built with the right switch at its core. Browse the full range of PoE switches and networking equipment at Big Mind Technologies for compatible IP cameras and surge protection accessories.

The School or Campus Network With Long Cable Runs

A school building with a 180-metre cable run to a far classroom block cannot connect at standard Ethernet distance. Extend mode on the DGS-F1010P covers 250 metres — placing access points at both ends of the campus from a single switch in the server room. QoS mode prioritises educational video streaming traffic over general browsing. VLAN mode prevents student devices from communicating with administration systems on the same switch.

The Hotel or Hospitality Property Deploying Cameras and APs

Eight PoE ports handle four outdoor perimeter cameras and four indoor wireless access points simultaneously. The 120W budget covers four 15W cameras and four 13W access points with headroom. PoE mode reboots any frozen access point automatically — no technician visit required at 3am when a guest reports no Wi-Fi. The fanless design runs silently inside a cupboard or service corridor. Full product specifications and datasheet are available on the official D-Link DGS-F1010P product page.

The Small Business With Unstable Power Infrastructure

In environments where power quality is inconsistent — frequent brownouts, grid switching, generator transitions — connected equipment is exposed to regular low-level surge events. The DGS-F1010P’s 6KV protection handles these events without degradation over time. A switch that absorbs hundreds of small surges across a year costs less than replacing cameras and access points that a lesser-protected switch would have destroyed across the same period.

The Big Mind Technologies Guarantee

Big Mind Technologies supplies genuine D-Link products backed by full manufacturer warranty coverage. The D-Link DGS-F1010P ships ready to install — plug it in, select your mode with the DIP switch, and the network runs. Contact our team before purchase to confirm PoE budget compatibility with your specific device list or deployment environment.